[问答]

8590A无法执行校准

问答对人有帮助，内容完整，我也想知道答案 0 我有一个8590A，它没有20-db衰减器平坦度或平坦度校准数据的校准数。我只用零手动输入这个，以便正确显示采集。但是现在我无法执行校准，因为它没有报告校准信号。查看Artekmedia从“生成新校准数据”下载的手册，“本章的这一部分在随附的变更单中提供。” 不幸的是，我没有这个更改表，也无法在任何地方找到它。有没有人碰巧有这个变更表或者可以告诉我如何生成适当的衰减器和平坦度校准？希望输入正确的校准数据可以正确检测校准信号。我已将其连接到示波器，因此生成了校准信号。谢谢！亚当以上来自于谷歌翻译以下为原文 I have an 8590A and it didn't have the calibration numbers in for the 20-db attenuator flatness or the flatness calibration data. I manually entered this with just zeros to get the acquisition to display properly. However now I am not able to perform calibration as it reports no calibration signal. Looking through the manual downloaded from Artekmedia under "Generating New Calibration Data" that "This section of this chapter is supplied in the accompanying change sheet." Unfortunately I don't have this change sheet nor am I able to find it anywhere. By any chance does anyone happen to have this change sheet or could tell me how to generate the proper attenuator and flatness calibrations? Hopefully entering proper calibration data would allow it to properly detect the calibration signal. I have connected it to my oscilloscope so there is a calibration signal being generated. Thanks! Adam 0
2018-9-12 15:42:14　　评论淘帖0 邀请回答您可以邀请以下用户，快速回答问题 × kingnet_52040 该类别下有 195 个回答。邀请回答 60user7 该类别下有 81 个回答。邀请回答蓝色冰汐该类别下有 45 个回答。邀请回答醉狼工作室该类别下有 41 个回答。邀请回答 ianwhoani 该类别下有 30 个回答。邀请回答 dkhwakd 该类别下有 25 个回答。邀请回答 aaabbb567 该类别下有 23 个回答。邀请回答 e08506806 该类别下有 20 个回答。邀请回答 szzjfyp 该类别下有 18 个回答。邀请回答 ningee 该类别下有 16 个回答。邀请回答 sonia87 该类别下有 16 个回答。邀请回答 zouqinxiang 该类别下有 15 个回答。邀请回答 xj5548 该类别下有 15 个回答。邀请回答 derek88 该类别下有 14 个回答。邀请回答 daichuangs 该类别下有 14 个回答。邀请回答 hzmbs2016 该类别下有 12 个回答。邀请回答 JST2006 该类别下有 12 个回答。邀请回答 bisong13 该类别下有 11 个回答。邀请回答 ToGoodSoft 该类别下有 11 个回答。邀请回答 www037 该类别下有 11 个回答。邀请回答举报骆其节相关推荐 • HP 8590A Freq和Ampl Cal信息在什么文档中有 1391 • 8590A升级/转换可提高其频率稳定性吗？ 1075 • 8590A扫描显示问题 1451 • 8590A显示抖动 1063 • 8590A具有小漂移和不稳定性 1974 • HP 8590频谱分析仪屏幕充满点 2086 • HP 8590A缺少HPIB/GPIB连接器和电缆 2198 • 8590L A16板的原理图 1729 • keil编程无法执行怎么办，win18 3927 • 8591A死电池，无法使用“RESET”启动恢复程序 1148 1个回答

答案对人有帮助，有参考价值 0 嗨亚当，先来几个问题。你有支持者吗？上电后，您是否在屏幕的最左侧看到了吸气？在改变因素之前，屏幕上是否显示300 MHz的校准信号？您是否使用特殊代码输入新值？只需输入20 dB误差因子。如果Cal sig，分析仪将自行校正实际值。有空！这可以在显示屏上看到4 4 CAL（更多）软键DISPLAY CAL DATA例如。 Artek支持人。第4-18页。当未显示校准300MHz时，第一个混频器不工作的可能性，两个二极管都有缺陷。亚当我会帮助你走上正轨！ 73 Ary pa0alv 以上来自于谷歌翻译以下为原文 Hi Adam, First a couple of questions. Do you have the support man ? Did you see aspike on the most left side of the screen after power up ? Was/is the cal signal of 300 MHz on the screen seen before altering the factors? Did you use the specialcodes for entering new value ? Only the 20 dB error factor need to be entered. The analyser will correct the actual value by itself, if the Cal sig. is available ! This is seen on the display p 4-17 CAL (MORE) soft key DISPLAY CAL DATA eg. Artek Support man. page 4-18 . When the cal sig 300MHz is not displayed the possibility excist the first mixer is not working, both diodes are defect. Adam I'll help you on track! 73 Ary pa0alv

2018-9-12 15:48:41 评论举报李小红